Provide NACE NACE-CIP1-001 Practice Test Engine for Preparation

Detailed New NACE-CIP1-001 Exam Questions for Concept Clearance

Individuals who successfully pass the NACE-CIP1-001 Certification Exam are awarded the Coating Inspector Level 1 certification. Coating Inspector Level 1 certification is recognized worldwide and is highly valued by employers in the coating industry. As a certified coating inspector, individuals have the opportunity to work in a variety of industries, including oil and gas, manufacturing, and construction. Coating Inspector Level 1 certification also opens up opportunities for career advancement and higher salaries.

 

NEW QUESTION # 10
Passivation can best be described as:

• A. Complete elimination pf the corrosion process
• B. Treating metal with a liquid inhibiter
• C. A coating layer applied to the surface to inhibit corrosion
• D. A protective metallic oxide surface layer that slows corrosion

Answer: D

NEW QUESTION # 11
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?

• A. 1 cm (.39 inch)
• B. 2.5 cm (1 inch)
• C. 6.35 cm (2.5 inch)
• D. 2.5 millimeters (.10 inch)

Answer: B

NEW QUESTION # 12
Check abrasive blast pressure close to the

• A. blast nozzle
• B. compressor
• C. blast pot
• D. substrate

Answer: A

NEW QUESTION # 13
The least effective method of surface cleaning is most likely

• A. dry grit blasting.
• B. water blasting.
• C. power tool cleaning.
• D. hand tool cleaning.

Answer: D

NEW QUESTION # 14
Daily reports are important because:
Select All That Apply

• A. the information impacts future projects.
• B. Inspectors rarely change on a project.
• C. The information aids communication with supervisors.
• D. Management uses them to make personnel decisions.

Answer: A,C,D

NEW QUESTION # 15
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:

• A. Call the coating manufacturer for clarification
• B. Call the person who wrote the specification for clarification
• C. Use the job specification as a guide
• D. Use the product data sheet as a guide

Answer: C

NEW QUESTION # 16
Owners hire NACE Inspectors' with the expectation that:

• A. The Inspector will improve job flow and schedule
• B. The inspection cost will be offset by an improvement in service life
• C. The Inspector will make a meaningful technical contribution to the job
• D. a) and c)

Answer: D

NEW QUESTION # 17
Upon arrival of coating materials, the inspector should

• A. observe aryl document that the applicator WFT at regular intervals during application.
• B. observe and document the amount of material and batch numbers.
• C. observe and document time frame and environmental conditions between each coat.
• D. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.

Answer: B

NEW QUESTION # 18
Check abrasive blast pressure with a

• A. nozzle aperature gauge
• B. needle pressure gauge
• C. surface comparator
• D. replica tape

Answer: B

NEW QUESTION # 19
NACE SP 0178 is a standard for:

• A. Stainless steel pipe to be Externally Coated
• B. Tanks and Vessels to be Externally Coated
• C. Tanks and Vessels to, be Lined for Immersion Service
• D. Structural steel to be coated for Atmospheric Service

Answer: C

NEW QUESTION # 20
Whenever dissimilar metals must join, the most common practice is to

• A. provide anodic protection to prevent corrosion.
• B. coat all connected dissimilar metals.
• C. provide cathodic protection to prevent corrosion,
• D. avoid coating all connected dissimilar metals.

Answer: B

NEW QUESTION # 21
The Inspector's Log Book is generally:

• A. Shredded by the inspector upon project completion
• B. Shared with all parties upon project completion
• C. Retained by the inspector upon project completion
• D. Submitted to the client upon project completion

Answer: C

NEW QUESTION # 22
Relative humidity is

• A. a measure of the amount of moisture in the air compared to the air temperature.
• B. the highest temperature at which moisture forms on a steel surface.
• C. the lowest temperature at which moisture forms on a steel surface.
• D. a measure of the amount of moisture in the air compared to saturation level.

Answer: D

NEW QUESTION # 23
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

• A. their best judgment based on similar projects and specifications.
• B. a detailed checklist and document the lack of a standard.
• C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
• D. NACE 2/SSPC SP10

Answer: C

NEW QUESTION # 24
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

• A. 225 Gauge Readings resulting in 75 Spot Measurements
• B. 45 Gauge readings resulting in 15 Spot Measurements
• C. 75 Gauge Readings resulting in 25 Spot Measurements
• D. 105 Gauge Readings resulting in 35 Spot Measurements

Answer: A

NEW QUESTION # 25
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:

• A. Accept the assignment without hesitation
• B. Meet with the prospective employer to determine the scope of your role
• C. Review the NACE Attestation prior to making a decision
• D. Advise the prospective employer that you cannot accept the position

Answer: B

NEW QUESTION # 26
Corrosion generally occurs at which of the following sites:

• A. Cathode
• B. Anode
• C. Metallic pathway
• D. Electrolyte

Answer: B

NEW QUESTION # 27
What is used to determine compressed air cleanliness?

• A. Psychrometer
• B. Profilometer
• C. Needle pressure gauge
• D. Blotter test

Answer: B

NEW QUESTION # 28
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:

• A. Level 4
• B. Level 3
• C. Level 2
• D. Level 1

Answer: B

NEW QUESTION # 29
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing

• A. develops a polished surface, which is a poor anchor profile for most coatings
• B. damages structural elements thereby speeding up the corrosion process.
• C. develops a good anchor profile resulting in uneven coating application.
• D. scratches the surface too deeply resulting in uneven coating application

Answer: A

NEW QUESTION # 30
......

NACE-CIP1-001 2024 Training With 100 QA's: https://www.examstorrent.com/NACE-CIP1-001-exam-dumps-torrent.html

NACE-CIP1-001 Exam Preparation Material with New NACE-CIP1-001 Dumps Questions.: https://drive.google.com/open?id=1ySSkeJkW2gLfGgWaQL0vtIqDwO48H3MQ