[Aug-2024] NACE NACE-CIP1-001 Official Cert Guide PDF
Exam NACE-CIP1-001: Coating Inspector Level 1 - ExamsTorrent
NEW QUESTION # 32
Which one of these elements is not necessary for corrosion to occur:
- A. Anode
- B. Electrolyte
- C. Reference Cell
- D. Cathode
Answer: C
NEW QUESTION # 33
The most important factor resulting in improved job site safety is:
- A. Personal Protective Equipment
- B. Safety Enforcement
- C. Engineering Controls
- D. Situational Awareness
Answer: D
NEW QUESTION # 34
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. alligatoring.
- C. blistering.
- D. checking.
Answer: D
NEW QUESTION # 35
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. soluble chemical salts
- B. sulfates
- C. inhibitor residues
- D. grease and oil
Answer: D
NEW QUESTION # 36
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Psychrometer
- C. Blotter test
- D. Profilometer
Answer: D
NEW QUESTION # 37
Galvanic corrosion occurs on which of the following substrates:
- A. Metal
- B. Wood
- C. Concrete
- D. Fiberglass Reinforced Plastic
Answer: A
NEW QUESTION # 38
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. blotter test for the presence of oil and water.
- B. wet film thickness (WFT) measurement.
- C. vial lest.
- D. dry film thickness (DEI) measurement.
Answer: A
NEW QUESTION # 39
If a Thermoset coating is heated it will:
- A. Harden and return to its original hardness when cooled
- B. Soften when heated and retain its softness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and return to its original hardness when cooled
Answer: C
NEW QUESTION # 40
Upon arrival of coating materials, the inspector should
- A. observe aryl document that the applicator WFT at regular intervals during application.
- B. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- C. observe and document time frame and environmental conditions between each coat.
- D. observe and document the amount of material and batch numbers.
Answer: D
NEW QUESTION # 41
Owners hire NACE Inspectors' with the expectation that:
- A. The Inspector will improve job flow and schedule
- B. a) and c)
- C. The Inspector will make a meaningful technical contribution to the job
- D. The inspection cost will be offset by an improvement in service life
Answer: B
NEW QUESTION # 42
An Inspector should change position when:
- A. The Inspectors position is not the majority position
- B. The Owner can save some money by the change
- C. The Inspector is convinced by verifiable facts
- D. Only when directed by the supervisor
Answer: C
NEW QUESTION # 43
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Bring the matter up at the pre-job conference
- B. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- C. Default to the owner's Inspection and Test Plan
- D. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
Answer: A
NEW QUESTION # 44
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- B. their best judgment based on similar projects and specifications.
- C. a detailed checklist and document the lack of a standard.
- D. NACE 2/SSPC SP10
Answer: A
NEW QUESTION # 45
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 70% of the specified maximum thickness
- B. 90% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 100% of the specified maximum thickness
Answer: C
NEW QUESTION # 46
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor he can proceed
- C. Advise the Contractor of your readings
- D. Advise the Contractor he cannot proceed
Answer: C
NEW QUESTION # 47
The NACE Inspector should perform tests for soluble salts:
- A. Prior to surface preparation
- B. When specified
- C. Prior to coating application
- D. After surface preparation
Answer: B
NEW QUESTION # 48
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. It depends on which hand tool the Contractor selects
- C. No, because there is no real difference in the standards
- D. It depends on which power tool the Contractor selects
Answer: C
NEW QUESTION # 49
......
Free NACE-CIP1-001 Exam Dumps to Improve Exam Score: https://www.examstorrent.com/NACE-CIP1-001-exam-dumps-torrent.html
2024 Realistic NACE-CIP1-001 Dumps Exam Tips Test Pdf Exam Materials: https://drive.google.com/open?id=1g7aDZDIeJEYDhEvRNLDZa0xwhsB3wlcM