(2024) PASS 300-410 Exam Free Practice Test with 100% Accurate Answers
300-410 dumps Free Test Engine Verified By It Certified Experts
NEW QUESTION # 94
Refer to the exhibit.
Which statement about R1 is true?
- A. RIP learned routes are distributed to OSPF with a tag value of one.
- B. RIP routes are redistributed to OSPF without any changes.
- C. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
- D. OSPF redistributes RIP routes only if they have a tag of one.
Answer: A
NEW QUESTION # 95
Refer to the exhibit.
The administrator successfully logs into R1 but cannot access privileged mode commands. What should be configured to resolve the issue?
- A. enable secret or enable password commands to enter into privileged mode
- B. aaa authorization reverse-access
- C. matching password on vty lines as cisco123!
- D. secret cisco123! at the end of the username command instead of password cisco123!
Answer: A
NEW QUESTION # 96
Refer to the exhibit.
An engineer identifier a Layer 2 loop using DNAC. Which command fixes the problem in the SF-D9300-1 switch?
- A. spanning-tree loopguard default
- B. spanning-tree backbonesfast
- C. no spanning-tree uplinkfast
- D. spanning-tree portfast bpduguard
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and management/dnacenter/tech_notes/b_dnac_sda_lan_automation_deployment.html
NEW QUESTION # 97
Refer to the exhibit.
Refer to the exhibit. A customer finds that traffic from the application server (192.168.1.1) to the HUB site passes through a congested path that causes random packet drops. The NOC team influences the BGP path with MED on RB. but RD still sees that traffic coming from RA is not taking an alternate route. Which configuration resolves the issue?
A)
B)
C)
D)
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: D
NEW QUESTION # 98
Refer to the exhibit.
An IT staff member comes into the office during normal office hours and cannot access devices through SSH Which action should be taken to resolve this issue?
- A. Configure the access list in the outbound direction.
- B. Configure the correct time range.
- C. Modify the access list to use the correct IP address.
- D. Modify the access list to correct the subnet mask
Answer: C
Explanation:
Explanation
To ACL should be permit tcp 101 10.1.1.1 0.0.0.0
NEW QUESTION # 99
Which protocol does MPLS use to support traffic engineering?
- A. Tag Distribution Protocol
- B. Label Distribution Protocol
- C. Resource Reservation Protocol
- D. Border Gateway Protocol
Answer: C
Explanation:
NEW QUESTION # 100
Drag and drop the MPLS VPN device types from me left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION # 101
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
- A. service timestamps log uptime
- B. clock summer-time mst recurring 2 Sunday mar 2:00 1 Sunday nov 2:00
- C. service timestamps log datetime localtime show-timezone
- D. clock calendar-valid
Answer: A
NEW QUESTION # 102
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
- A. Change the mode from mode transport to mode tunnel on R2.
- B. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- C. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3.
- D. Change the mode from mode tunnel to mode transport on R3.
- E. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
Answer: C,E
Explanation:
The first six commands are used to configure IPSec Phase 1 (ISAKMP Policy). Here is the details of each command used above: + crypto isakmp policy 10 - This command creates ISAKMP policy number 10. You can create multiple policies, for example 7, 8, 9 with different configuration. Routers participating in Phase 1 negotiation tries to match a ISAKMP policy matching against the list of policies one by one. If any policy is matched, the IPSec negotiation moves to Phase 2. + hash md5- MD5 algorithm will be used. + authentication pre-share - Authentication method is pre-shared key.
+ group 2 - Diffie-Hellman group to be used is group 2. + encryption 3des - 3DES encryption algorithm will be used for Phase 1. + crypto isakmp key cisco address 10.1.1.1 - The Phase 1 password is cisco and remote peer IP address is 10.1.1.1 The next two command lines are used to configure IPSec Phase 2 (Transform Set): + crypto ipsec transform-set <transform-set-name> - Creates transform-set called <transform-set-name> + esp-des - ESP IPSec protocol with the 56-bit Data Encryption Standard (DES) encryption algorithm will be used + esp-md5-hmac - ESP with the MD5 (HMAC variant) authentication algorithm will be used. + mode transport: only encrypts the payload and ESP trailer or + mode tunnel: encrypts the IP header of the ENTIRE packet
NEW QUESTION # 103
Refer to the exhibit.
An engineer must configure a LAN-to-LAN IPsec VPN between R1 and the remote router. Which IPsec Phase 1 configuration must the engineer use for the local router?
- A. crypto isakmp policy 5
Answer: A
Explanation:
authentication pre-share
encryption 3des
hash sha
group 2
!
crypto isakmp key cisco123 address 200.1.1.3
B.
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123 address 200.1.1.3
C.
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123 address 199.1.1.1
D.
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash md5
group 2
!
crypto isakmp key cisco123! address 199.1.1.1
Explanation:
Explanation
In the "crypto isakmp key ... address " command, the address must be of the IP address of the other end (which is 200.1.1.3 in this case) so Option A and Option B are correct. The difference between these two options are in the hash SHA or MD5 method but both of them can be used although SHA is better than MD5 so we choose Option A the best answer.
Note: Cisco no longer recommends using 3DES, MD5 and DH groups 1, 2 and 5.
Reference:
5/sec-ipsec-management-xe-16-5-book/sec-ipsec-usability-enhance.html
NEW QUESTION # 104 
Refer to the exhibit. The IT router has been configured with the Science VRF and the interfaces have been assigned to the VRF. Which set of configurations advertises Science-1 and Science-2 routes using EIGRPAS
111?
- A. Option B
- B. Option A
- C. Option C
- D. Option D
Answer: D
NEW QUESTION # 105
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION # 106
While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?
- A. The software image for the device is in bundle mode
- B. The software image for the device is in install mode.
- C. The device must be resynced to Cisco DNA Center.
- D. The device has lost connectivity to Cisco DNA Center.
Answer: B
Explanation:
Explanation
Upload Software Images for Devices in Install Mode
The Image Repository page might show a software image as being in Install Mode. When a device is in Install Mode, Cisco DNA Center is unable to upload its software image directly from the device. When a device is in install mode, you must first manually upload the software image to the Cisco DNA Center repository before marking the image as golden, as shown in the following steps.
Reference:
https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-andmanagement/ dna-center/1-2-10/user_guide/b_cisco_dna_center_ug_1_2_10/ b_dnac_ug_1_2_10_chapter_0100.html
NEW QUESTION # 107
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
By default BGP advertises all prefixes to external BGP neighbors. This means that if you are multi-homed (connected to two or more ISPs) then you might become a transit AS. For example, ISP 2 in AS 200 can send traffic to your router in AS 100 to reach ISP 3 in AS 300 because you advertised prefixes in ISP 3 to ISP 2.
This is what will be seen in the BGP routing table of ISP1:
NEW QUESTION # 108 
- A. access-list 20 permit 10.221.10.11
- B. access-list 20 permit 10.221.10.12
- C. snmp-server group NETVIEW v2c priv read NETVIEW access 20
- D. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22
Answer: A
NEW QUESTION # 109
Refer to the exhibit.
An administrator is troubleshooting a time synchronization problem for the router time to another Cisco IOS XE-based device that has recently undergone hardening. Which action resolves the issue?
- A. Allow NTP in the ingress ACL on 10.1.255.40 by permitting TCP destined to port 123.
- B. Allow NTP in the ingress ACL on 10.1.225.40 by permitting UDP destined to port 123.
- C. Ensure that he CPE router has a valid route to 10.1.255. 40 for NTP and rectify if not reachable.
- D. NTP service is disabled and must be enabled on 10.1.225.40.
Answer: D
NEW QUESTION # 110
Refer to the exhibit.
Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and ignores BGP traffic that is sent at higher rate?
- A. policy-map LIMIT_BGP
- B. policy-map POLICE_BGP
- C. policy-map COPP
- D. policy-map SHAPE_BGP
Answer: C
NEW QUESTION # 111
Refer to the exhibit.
Refer to the exhibit. The OSPF neighbor relationship is not coming up What must be configured to restore OSPF neighbor adjacency?
- A. use router ID
- B. OSPF on the remote router
- C. matching hello timers
- D. matching MTU values
Answer: D
NEW QUESTION # 112
......
Cisco 300-410 exam, also known as Implementing Cisco Enterprise Advanced Routing and Services, is designed for IT professionals who are interested in advancing their knowledge and skills in enterprise networking. Implementing Cisco Enterprise Advanced Routing and Services certification exam is part of the CCNP Enterprise track and focuses on advanced routing technologies and services such as BGP, OSPF, and PBR. Passing 300-410 exam will demonstrate your ability to configure, troubleshoot, and optimize complex enterprise networks.
Latest Cisco 300-410 Practice Test Questions: https://www.examstorrent.com/300-410-exam-dumps-torrent.html
Realistic 300-410 Accurate & Verified Answers As Experienced in the Actual Test!: https://drive.google.com/open?id=1pKDq_NLa3mJjMI3a0GzIJm1xiy1pDMUW