Aug 31, 2026 NACE-CIP1-001 Exam Crack Test Engine Dumps Training With 100 Questions

Obtain the NACE-CIP1-001 PDF Dumps Get 100% Outcomes Exam Questions For You To Pass

What is the Passing Score, Duration & Question for the NACE CIP1-001 Exam?

• Languages: English
• No. of questions: 100
• Exam Format: Multiple choice
• Duration Exam: 2 hours
• Passing score: at least 50%

 

NEW QUESTION # 41
Silicone coatings are typically:

• A. Used as a sacrificial primer
• B. Applied in very' thin films
• C. Used strictly in immersion service
• D. Applied in very thick films

Answer: B

NEW QUESTION # 42
What is used to determine compressed air cleanliness?

• A. Blotter test
• B. Psychrometer
• C. Needle pressure gauge
• D. Profilometer

Answer: D

NEW QUESTION # 43
If a Thermoset coating is heated it will:

• A. Harden and retain its hardness when cooled
• B. Soften when heated and retain its softness when cooled
• C. Harden and return to its original hardness when cooled
• D. Soften when heated and return to its original hardness when cooled

Answer: A

NEW QUESTION # 44
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

• A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
• B. Carefully review the document and do the best you can
• C. Advise the owners' representative of your lack of knowledge in this area
• D. Hire a third patty to assist you in understanding the document

Answer: B

NEW QUESTION # 45
Checking is

• A. an exposed area of the substrate or previous coat material, caused by poor application technique.
• B. a fine crack in the surface of a coating that rarely reaches the substrate
• C. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
• D. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.

Answer: B

NEW QUESTION # 46
A NACE Coating Inspector is permitted to transport coating material when:

• A. The Inspector should never transport coating material
• B. Asked to do so by the Owner's Representative
• C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
• D. Asked to do so by the Coating Application team

Answer: A

NEW QUESTION # 47
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:

• A. juxtaposing.
• B. monitoring
• C. telegraphing.
• D. transitioning.

Answer: C

NEW QUESTION # 48
The least effective method of surface cleaning is most likely

• A. hand tool cleaning.
• B. water blasting.
• C. power tool cleaning.
• D. dry grit blasting.

Answer: A

NEW QUESTION # 49
Check abrasive blast pressure close to the

• A. blast pot
• B. substrate
• C. compressor
• D. blast nozzle

Answer: D

NEW QUESTION # 50
Non Conformance Reports are completed by the Inspector:

• A. In every instance that an item does not meet the specification requirements
• B. In accordance with the specification's definition of a non-conformance
• C. When the Inspector deems it to be a significant non-conforming item
• D. When the Inspector and Contractor deem it to be a significant non-conforming item

Answer: D

NEW QUESTION # 51
A magnetic pull-off type gauge is a good choice when:

• A. When working on non-ferrous metals
• B. Accuracy is not required
• C. When an intrinsically safe tool is required
• D. Performing an adhesion test

Answer: C

NEW QUESTION # 52
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:

• A. Meet with the prospective employer to determine the scope of your role
• B. Review the NACE Attestation prior to making a decision
• C. Accept the assignment without hesitation
• D. Advise the prospective employer that you cannot accept the position

Answer: A

NEW QUESTION # 53
Dew point is the temperature at which

• A. condensation occurs.
• B. water freezes.
• C. humidity decreases
• D. the air is saturated.

Answer: A

NEW QUESTION # 54
Passivation can best be described as:

• A. A protective metallic oxide surface layer that slows corrosion
• B. A coating layer applied to the surface to inhibit corrosion
• C. Treating metal with a liquid inhibiter
• D. Complete elimination pf the corrosion process

Answer: A

NEW QUESTION # 55
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:

• A. Level 4
• B. Level 3
• C. Level 2
• D. Level 1

Answer: B

NEW QUESTION # 56
ISO SA 3 is directly equivalent to:

• A. NACE No. 1/SSPC SP 5
• B. None of the above
• C. NACE No. 2/SSPC SP 10
• D. NACE No. 3/SSPC SP 6

Answer: B

NEW QUESTION # 57
Which of these tests uses a syringe?

• A. Bresle patch
• B. Sleeve test
• C. Potassium ferricyanide
• D. Soluble salts meter

Answer: A

NEW QUESTION # 58
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing

• A. develops a polished surface, which is a poor anchor profile for most coatings
• B. damages structural elements thereby speeding up the corrosion process.
• C. scratches the surface too deeply resulting in uneven coating application
• D. develops a good anchor profile resulting in uneven coating application.

Answer: A

NEW QUESTION # 59
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use

• A. their best judgment based on similar projects and specifications.
• B. a recognized industry standard like SSPC-PA 2 that is broadly accepted
• C. NACE 2/SSPC SP10
• D. a detailed checklist and document the lack of a standard.

Answer: B

NEW QUESTION # 60
Stripe coats are best applied by:

• A. Brush
• B. High volume low pressure spray
• C. Conventional spray
• D. Airless spray

Answer: A

NEW QUESTION # 61
Which one of these elements is not necessary for corrosion to occur:

• A. Anode
• B. Reference Cell
• C. Electrolyte
• D. Cathode

Answer: B

NEW QUESTION # 62
NACE No. 4/SSPC-SP-7 is a joint standard for

• A. near-white metal blast cleaning.
• B. white metal blast cleaning.
• C. brush-off blast cleaning.
• D. commercial blast cleaning.

Answer: C

NEW QUESTION # 63
NACE SP 0178 is a standard for:

• A. Stainless steel pipe to be Externally Coated
• B. Tanks and Vessels to, be Lined for Immersion Service
• C. Structural steel to be coated for Atmospheric Service
• D. Tanks and Vessels to be Externally Coated

Answer: B

NEW QUESTION # 64
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:

• A. Go with the majority opinion
• B. Never change his/her mind
• C. Achieve consensus through negotiation
• D. Call the supervisor

Answer: D

NEW QUESTION # 65
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: D

NEW QUESTION # 66
......

NACE-CIP1-001 Exam Dumps Contains FREE Real Quesions from the Actual Exam: https://www.examstorrent.com/NACE-CIP1-001-exam-dumps-torrent.html

Free Test Engine Verified By CIP Level 1 Certified Experts: https://drive.google.com/open?id=1As917CtnGnfQ27HyQddMq4VMsATEoo86